MAJIC MX JTAG Interface Controller with Manual
MAJIC-MX Multi-processor Advanced JTAG Interface Controller with
MAJIC-MX MDSS Development System Features:
* Ideal for multiple core SoC
* Provides EPI MDSS
* Supports execution tracing with
on-chip trace buffers
* FLASH memory programming
* Supports a wide choice of
on-chip debug interfaces
* Supports a wide variety of CPU
* Supports on-chip hardware
* Unlimited software
* Programmable JTAG clock (TCK =
0 to 40 MHz)
* Programmable trigger-in and
* Ethernet and serial I/O ports
for fast, flexible host interface
* High-speed download of
* Network compatibility allows
shared and remote operation
* Internal RISC Processor
provides on-probe intelligence
* Wide selection of Configuration
Kits extends usage to multiple architectures
* Sleep-mode support
* LEDs display operation
* Operates with most third party
debuggers via industry standard APIs
* Optional EDB integrated
* Interfaces for popular OS
non-intrusive debug solution for your multiple core SoC and high
CPU pipeline speed designs. Now, you can have the same level of
control and visibility of the embedded CPU as you would with
in-circuit emulators in traditional discrete CPU designs. The
result is faster software integration, better testing, and improved
time to market.
probe is the latest model in the MAJIC Series of intelligent debug
probes. The series now supports scaling of SoC devices to unlimited
clock rates and to unlimited number of on-chip cores. MAJIC-MX
probe embodies the new EPI MDSS debug concept. This concept allows
fast integration and debugging of software for complex SoC devices.
It recognizes that SoC designs are rapidly scaling up in both
pipeline speeds and complexity. Thus, MDSS supports:
Multi-context CPUs, and
On-chip trace buffers.
probe provides a high-speed hardware interface between processors
with an on-chip debug interface and industry standard debuggers. It
is available with a choice of EPI debuggers and may be used with
used with task-aware debuggers from leading OS vendors. The unit is
self-contained in a small case approximately 2 x 6.5 x 7.5 inches
non-intrusive MAJIC-MX probe communicates with the CPU core by JTAG
interface using the existing boundary scan pins. For most on-chip
debug facilities, it uses no target memory and requires no porting
to the target system.
processor control means you can start, stop and single-step
execution; read and write to registers, memory, and system I/O; and
download code to target RAM - all within most industry standard
memory tests assist in hardware testing. And the EPI open-source
flash programming algorithm allows programming of flash memory
located either internal or external to the SoC device.
probe expands to support additional cores, debug interfaces, or SoC
devices. This eliminates the need to buy new emulators for each new
project, thus reducing project costs.
You may adapt
the MAJIC-MX controller for operation with your specific processor
or CPU cores by selecting from a wide range of configuration kits.
The kits contain the firmware and user license to match your CPU's
on-chip debug facilities. Install multiple configuration kits, and
the MAJIC-MX probe will support a variety of CPU types.
controller is ready to run with the EPI software tools and any
development board that supports a connection to the on-chip debug
interface. This combination of tools will work together to provide
you with a proven working environment.
controller is available as a stand-alone unit or as a complete
debugging kit. The kit contains serial and Ethernet cables,
source-level debugger, and one year of free maintenance, support,
and updates. Part number: MAJIC-MX-KIT.
development kits are also available that include a compilation
toolkit. See the EPI Price and Configuration Guide for full details
of these development kits.
the MAJIC-MX probe include:
Multi-Dimensional Scaling Support for SoC Devices
probe embodies the new MDSS debug concept. This concept allows fast
integration and debugging of software for complex SoC devices. To
support SoC designs that are rapidly scaling up in both pipeline
speeds and complexity, MAJIC-MX probe supports:
Multi-context CPUs, and
On-chip trace buffers.
controller supports full execution tracing from CPU cores that
offer on-chip trace buggers. Trace control allows tracing from
start of execution or tracing up to a breakpoint.
Ethernet interface provides many advantages over serial or parallel
interfaces to the host. Download of your application code is over
ten times faster than with serial interface. This will
significantly reduce the amount of time spent waiting for code
changes to download to your target board.
Network connection allows remote operation of the MAJIC-MX
probe. Now you can access the lab setup directly from your desktop.
This allows multiple engineers to share a common test bench.
of a MAJIC-MX probe is easily upgraded without the need to replace
install new configuration kits to add support for multiple CPU
types and easily program IP address into the unit for
point-to-point Ethernet operation.
Internal RISC Processor
high-performance internal RISC processor provides fast response to
debugger operations, such as single-stepping and downloading code
to the target.
Programmable JTAG Clock
probe features a programmable TCK with a 0 to 40 MHz range. This
allows you to tailor the JTAG operation to match the performance of
your target. It also means that you can use the MAJIC-MX probe with
low-speed ASIC emulators, with FPGA implementation of your SoC
design, or with devices that feature sleep-mode operation.
Convenient Reset Switch
reset button on the MAJIC-MX probe is protected against accidental
activation, yet is easily accessible by the user when a complete
system reset is desired.
Programmable Trigger Control
probe gives you control over both the trigger-in and trigger-out
signals. The trigger-in signal may be used to create a breakpoint
or synchronize execution. A trigger output may set to indicate
execution status, indicate memory accesses, or indicate a memory
probe provides five LEDs, which show the operational status of the
controller. These LEDs also indicate the results of the built-in
self-test that is automatically performed upon startup.
International Power Supply
probe operates from a standard 5V power source. It comes with an
external UL/CE-approved AC adapter, whose AC input range is
compatible with all international AC voltage and frequency ranges.
A standard three-wire power connector is compatible with readily
available power cords through the world.
clock(TCK): 0 to 40 MHz, Programmable
speed: >100k bytes/sec (typical)
voltage: 1.8 to 5.0V
interface: 10/100Base-T, TCP/IP
Trigger In: Off, run
Trigger Out: Off, run
sync, memory access, memory test error
LEDs: Power, status, run, connect, Ethernet
(inches): 2.0 H x 7.4 W x 6.5 L
5 VDC +/- 5%, 4.0 A
connector: 2.1 mm coaxial, center positive, male
0 - 40 degrees C (Operating)
- 95% RH (Operating)
Item is in
good physical condition and came from a working business that
closed. Item powers up.
Includes power adapter Jtag cable, users/programmers manual.
Don't forget to place
By bidding on this auction you agree to the following
Buyer pays all shipping
Let us know if there is
an issue with the shipping costs, as they are automatically
calculated by ebay.
Shipments made to
California must include 8.75% sales tax unless we are provided with
a valid resale certificate.
We reserve the right to
ship with Fedex ground, USPS and any other carrier in the best
interests of the buyer and seller.
The Parcel post option
is only available to alaska, Hawaii, and US territories only. If
you select parcel post and you live in the lower 48 states you
package may be sent by another carrier and/or an additional
shipping amount may be required.
Payment is to be made
by PayPal in U.S. funds.
Please contact us if
you have any questions about ebay's recent payment policy
Payment is to be
received within ten days of close of auction.
Should payment not be
received within ten days the item will be re-listed and high bidder
No personal checks will
International Terms: (These terms only apply to international
Buyer is responsible
for all brokerage, customs, and or duty charges.
Not all items are
available for international shipment due to import/export
regulations. In the event that we are unable to ship to buyers
country, buyer will receive a full refund.
Payment must be made in
Money must be drawn
against a US bank.
No warranty nor
guarantee is expressed or implied regarding: usability,
functionality, merchantability, or cosmetic appearance of the
item(s) in auction.
What you see in the
picture(s) is what you get nothing more nothing less.
Test results of item(s)
in auction are described to the best of our ability in the ad. The
results of all tests that are performed are disclosed in the
Items sold as
"Untested" are simply that we have been unable to test the item(s)
due to missing cables/adapters/toner cartridge/ksu/etc, lack of
time, or other restrictions, Such as when we sell a laptop that we
don't have an AC adapter for.
Our only guarantee is
that you will receive the make and model listed in the ad.
The maximum liability
of BetterBizequipment(the seller) is the high bid of the
Returns are only
allowed under cases of gross misrepresentation in the ad, such as
when we describe a monitor as a fax machine. Such claims of
misrepresentation must be filed within three days of receipt of
shipment. Betterbizequipment reserves the right to replace the
item(s) or refund the high bid solely at our discretion. Item must
be returned in the original box and packaging.
Bidder must request a
RMA number before returning item(s).
without a RMA number will become property of Bbetterbizequipment
ten days after receipt unless buyer has paid return shipping within
the ten day period.
Shipping Damage Terms:
Seller will file a
shipping claim(s) upon behalf of the buyer with common carrier in
the event shipment(s) is/are damaged during shipping, in most
Not retaining the
original box and packaging may affect the carriers decision on a
Seller will commence
filing the claim once buyer has filed the damage report with the
Buyer must notify
seller within 48 hours of receipt of a damaged shipment.
The following terms
apply to any and all medical items or any item offered for sale in
any medical category or any item that eBay deems these terms are
The sale of this item
may be subject to regulation by the U.S. Food and Drug
Administration and state and local regulatory agencies. If so, do
not bid on this item unless you are an authorized purchaser. If the
item is subject to FDA regulation, I will verify your status as an
authorized purchaser of this item before shipping of the
The buyer will not hold
the seller, eBay or the item's manufacturer responsible for the
appropriate or inappropriate use of this device either by the user
or a third party. Once purchased, it is the sole responsibility of
the purchaser to assume any and all liability from the use of this
Please note before
bidding that any medical equipment purchased should be completely
tested by a qualified biomedical technician prior to being put into
service. Jason Rydell in San Diego, CA, USA Phone: 619-519-0869
Online Business name: Betterbizequipment
If any provision of
this Auction Contract is held unenforceable, All remaining
provisions of this Contract shall remain in full force and
2011 Betterbizequipment - All Rights Reserved.