Brand New CAN-BUS OBD II OBD2 Code Reader USB PC INTERFACE

The Best Solution to Diagnose All 1996 and Newer OBD2 Compliant Vehicles (including CAN-BUS)

More Features for Less: Access Same Information as Expensive Scanners!

FIT CAN-BUS HONDA/GM/FORD/NISSAN/TOYOTA ETC...

Software support Vista/xp/2000/98/me/95

European Vehicles
If your petrol passenger vehicle was manufactured for sale in Europe, with the model year of 2001 or newer (and in some cases 2000), you have the EOBD / OBDII interface. EOBD diesel vehicles start with the 2004 model years. Some Asian models such as Subaru were OBD-II before 2000. 

A PC running Windows: It is recommended to use at least a Pentium-100 (or AMD equivalent) with 16MB of RAM and Windows 95 or newer.  software may work on some lesser PC's, but anything less than the above recommendation is unsupported. Windows 95, 98, ME, NT4, 2000, and XP vista are all fine. Available disk-space is a total non-issue, software requires less than 1 MB.

Will This Code Reader Work with My Car?( MUST READ)

A small number of 1994 and 1995 model year gasoline vehicles are OBD II compliant. To verify if a 1994 or 1995 vehicle is OBD II compliant, check the Vehicle Emissions Control Information (VECI) Label which is located under the hood or by the radiator of most vehicles. If the vehicle is OBD II compliant, the label will designate “OBD II Certifiedâ€. Additionally, Government regulations mandate that all OBD II compliant vehicles must have a “common†sixteen-pin Data Link Connector (DLC).

For your vehicle to be OBD II compliant, it must have a 16 pin DLC (Data Link Connector) under the dash and the Vehicle Emission Control Information Label must state that the vehicle is OBD II compliant. This label is located on the inside of the hood on most vehicles.

VEHICLE COVERAGE
GM '96 - Current Year (OBD-II)
Ford '96 - Current Year (OBD-II)
Chrysler '96 - Current Year (OBD-II)
Toyota '96 - Current Year (OBD-II)
Honda '96 - Current Year (OBD-II)
NISSAN '96 - Current Year (OBD-II)
All other Asian and European '96 - Current Year (OBD-II )

• For laptops and PCs, download the shareware scantoo_net
• Run it and follow the prompts to allow it to install itself.
  Note: You must install software on your PC's hard disk -- it will not work properly if you try running it directly from a floppy or CD. However, you can use a floppy or CD to move the distribution file from a PC with internet access to another PC that does not have internet access.
• Connect the interface between the computer and the car by plugging one end of the interface into a Serial (RS232) (or USB port ) on your PC and the other end directly into the OBD-II port present in all 1996 and newer OBD2 passenger vehicles.
  
• Turn the car's ignition switch ON. No need to start the engine.
• Start the  software program, click "Options", select the correct communications port. Use "Test" to confirm that the program can use the port and find the interface. Then "Save".
• Now it works. Make sure the software can reliably access all the control modules that it should in your car.

Read diagnostic trouble fault codes, both generic and manufacturer-specific, and display their meaning (over 3000 generic fault code definitions in the database). · Clear fault trouble fault codes and turn off the MIL ("Check Engine" "Service soom"light) · Show current sensor data, including: o Engine RPM o Calculated Load Value o Coolant Temperature o Fuel System Status o Vehicle Speed o Short Term Fuel Trim o Long Term Fuel Trim o Intake Manifold Pressure o Timing Advance o Intake Air Temperature o Air Flow Rate o Absolute Throttle Position o Oxygen sensor voltages/associated short term fuel trims o Fuel System status o Fuel Pressure